7 Clever Ways to Hide TV Cords

Prevent idiot box cord clutter from becoming a misdirection with these creative result .

Grant Webster

Picture this : You in conclusion fling on that new telly you were eyeing . You get itmounted to the wall , hook up all of the connections , and sit down to watch your preferent show . Except it ’s hard to relax when you have a topsy-turvy hole of corduroys staring back at you .

TV mounted on wall in living room

Credit:Grant Webster

Many of today ’s TVs function as both entertainment and interior decoration , especially with the raise of framed flat screen that display art when turn off . Cord jumble can detract from the aesthetic you ’re aiming for and stand out against bloodless orneutral walls . The good news is that there are a variety of ways you’re able to mask television receiver wire to give you a seamless view , whether you ’re get a solo Netflix bout sitting or think about Edgar Albert Guest . Here are seven cagy way to hide unsightly video electric cord .

1. Hide Within the Wall

The most effectual method to hide out boob tube cords is also the one that requires the most elbow grease . hold in cable behind a paries makes them almost invisible from any slant . to do this , you ’ll need to mark and cut two holes in the paries — one at the bottom of where the TV hangs on the bulwark and the 2nd near the power wall plug below — using a hole image . From there , low voltage angle bracket or box seat need to be instal before running the wires from top to bottom . This allow cords to be plugged in at the entrance and exit level , give you a blank canvas between the bottom of the TV and the top of whatever console table or cabinet you post below it .

2. Cover with a Cable Raceway

A exchangeable ( but simpler ! ) way to shroud cord for a mounted TV is with a cable concealer kit , also know as a cable raceway . It ’s a smooth , flat polyvinyl chloride cover that attaches directly to the bulwark with adhesive material , allowing you to avoid drilling any additional gob . Cable raceways track down the distance of the wires and can be well cut to fit any sizing or layout you need , meaning you may climb up the TV wherever work good . All you have to do is bundle the cords together before crack the cover on top . you may also paint over cable race ; just check that to use the exact color of your walls so they seamlessly mix together .

3. Choose a TV Stand with an Outlet

Perhaps you ca n’t ( or do n’t need to ) climb on your TV to the wall , whether you ’re rent your home or not convinced in your DIY skills . you could still achieve a streamlined flavour by identify your boob tube on top of a surface . take a cabinet , cabinet , or entertainment center with an opening in the back to course cords through . To further hide optic clutter , opt something with at least one cabinet room access to invest the cable box and/or router behind , then feed the cords through the back and up to the television . You ’ll most likely see a small section of wire , but it will be underage compare to having the loge sit on the floor or on top of the TV stand .

4. Bundle Cords

For a flashy tv set corduroy solvent , bundle wires together . This will importantly reduce the chaos of corduroy move in different way . Clips , zip tie , adhesive hook shot , and coiled sleeve can all be used to corral idiot box cable together into a slim inclosure . The best way to put this to apply is by pinning them along the baseboard behind the goggle box or the back of the piece of piece of furniture that it sits on or above . For a budget - favorable pick , cut pieces off of a Velcro roll to wrap and contain TV corduroys .

Some cords ( such as the power cord on a cablegram loge ) might belong to the cable provider and need to be return if you switch services . place all the cords ahead of metre remove out the guesswork and rough-and-tumble . Take sentence to direct and label each cord with stickers , mark what each cord stop up into .

5. Place on a Console Table

An easygoing way to invalidate people seeing cables and cords is to keep your TV at oculus level and copulate it with acredenza or console board . To do this , either mount your telecasting lower in your elbow room or send it on a low - baby-sit console . Tuck the cables and cords behind the cabinet , zip - tieing them together to keep them tidy , then grace the mesa with artistic creation , flowers , and other decor token to completely hide the cords .

6. Use a Cable Box

Cable entrepot boxes are becoming pop , peculiarly as a fashion tokeep home offices elevatedand unionize . These subtle , often neutral rectangular boxwood are available in dissimilar sizes and design tosupport power strips , along with plug of all sizes and the mass of the excess wires . Find one in your animation elbow room ’s stylus and place it on the floor near the vent and cable jack .

Chad R. Mellon

7. Install Decorative Wall Treatments

Installing decorative wall treatments likewainscoting , slatted wood paneling , shiplap , and beadboard is another agency to hide TV cables and cord . Not only will a paries treatment add to your space and distract from plaguey TV cords , but it also allow for cord to fit alongside the paneling . For slat wall panel and shiplap , apply velcro strip or small adhesive hooks to trace the electric cord along the seams in the paneling .

If you opt for wainscoting , set up the panelsan column inch in front of the wall , permit quad for a channel for your cords . Use a conduit to amass and hold your electric cord . Or integrate a cablegram raceway into your wainscotting or beadboard pattern to seamlessly veil your television cords and cables .

TV wires under cable raceway