DIY PVC Grow Light Stand

Here’s a grow light stand your seedlings and wallet will appreciate.

There comes a full point in every nurseryman ’s liveliness when starting your own transplantation from seed not only make economic sense , but also opens up a whole novel cosmos of varieties that are available to you . Two priceless purchases that need to be consider are estrus mats and grow lights .

Regarding grow light systems , there are many options usable to you , at different sizes and manner . regrettably , most of these can come with a steep cost . The unity I researched online were in the neighbourhood of $ 150 - 200 orhigher .

While these were of reasonably good quality , it made me await for more cheap options . So I volunteer you a introductory DIY uprise light tie-up made entirely of PVC ( with required metal hardware ) . I was able to progress one of these for less than $ 60 , include the light fixture itself .

This aim ’s measurements will yield a grow light stand that supports a 4 - foot ( 48″ ) blanket fluorescent fixture shoplight fixing . you’re able to sure contrive it to agree a littler one that carries a 3- or 2 - invertebrate foot regular .

The listing of thing you ’ll necessitate :

• 48″ Fluorescent matching - electric-light bulb shoplight fixture with recommended bulbs ( 1).(BTW , I pick out one with a metal surface that would reflect more brightness level ( and because it look nerveless ! )

• 10 - ft duration of 1 1/4″ ( 1.25 ) premature ventricular contraction tubing ( 2 )

• Two 2 - foot ( 24″ ) while of 1″ PVC tubing ( 3 )

• Two 1 1/4″ ( 1.25 ) “ Tee ” PVC connector ( 4 )

• Two 1 1/4″ ( 1.25 ) 90 - degree “ elbow ” PVC connectors ( 5 )

• Four 1 1/4″ ( 1.25 ) PVC last caps ( 6 )

• Two stave bolts or equivalent , and their follow nuts . I would recommend 1/4″ diam by 3″ bolts

• Pack of two 1/4″ x 4″ “ eye draw ” and their accompanying nuts .

• Pack of two 1″ “ S - hooks ”

• Drill and categorization of practice session routine

• Hacksaw or PVC veer tool

• Tape criterion

• PVC cement

• Pen or permanent marker

• Timer

Skill Level :

Photo/Illustration: Greg Holdsworth (All)

gentle to arbitrate , depend on your craft and cutting skills .

Construction :

1 . Gather all of the needed part and tools(Photo A ) .

DIY Trellis

2 . cut down a distance of the 1 1/4″ premature ventricular contraction tube long enough to go beyond the length of your fluorescent idle repair . For the 4 - fundament mend , I reduce a small-arm about 55″. Then paste one of the elbow connectors to each end . You now have the “ top support legal profession ” completed(Photo B ) .

3 . Cut 4 equal length of the 1 1/4″ PVC tubing to suffice as support “ stage ” . These can be whatever length you wish , but I would n’t go any shorter than 8″. I tailor mine to 10″(Photo light speed ) .

4 . Take two of those 4 equal duration pieces and glue them to the Tee connection . Then glue two of the 4 terminal caps to that . You have now finished one of the “ leg tie-up ” . Repeat this stride for the second leg stand(Photo D ) .

DIY Trellis

5 . track 2 more equal length of the 1 1/4″ premature ventricular contraction tube , and glue into the ending of the “ top support stripe ” you finished in STEP # 2 . I made mine about 2 1/2″ ( 2.5 ) , but that length can be between 2 - 6″(Photo vitamin E ) .

6 . Cut 2 more equal lengths ( again ) of the 1 1/4″ PVC tube to serve as the “ riser ” come up from the peg stand . These can again be whatever distance you wish . I made mine about 6″. These bit are one of the two pieces that will raise and lour the luminance fixture(Photo F ) .

Yep , that ’s right ! This baby is adjustable . Not the fancy mechanism that the more expensive commercial I have , but it will do the job . Here ’s how it find :

DIY Trellis

7 . Insert one of the 1″ PVC tubing pieces into the “ branch stands ” you stop in STEP 4 . This is the other piece that will determine how tall your light fixture is raised . Drill a hole into BOTH the outer 1 1/4″ AND the intimate 1″ pieces of PVC tubing . The kettle of fish diameter should be wide enough to set aside the adjustment bolts to go in and out of the hole easily . Repeat this for the other side(Photo G ) .

This is thelowestpoint that the wakeful fixture will be , so keep that in psyche . Remember to compensate for the tiptop of your seed tray . Yes , you’re able to also line up the chains on the weak fixture , but this way is easier .

8 . Take both of the 1″ PVC pieces out , and mark 4 - 5 points , in 1″ increments , to the LEFT of the maw that you antecedently drilled . These will be the unlike position you’re able to elicit the idle habitue with(Photo H ) .

DIY Trellis

9 . Using the pen marks as a guide , drill the other holes . If you put the piece with the hole back into the base , you may now see how the reparation will be parent and lowered(Photo I ) .

10 . Put the top support bar onto the two peg pieces and you ’re almost finished(Photo J ) .

11 . Drill two holes , at adequate distance from each side , on the top of the support bar . Put in the center hook , “ hole ” in bottom . These will connect to the chains provide by the light fixture(Photo K ) .

DIY Trellis

12 . Unpackage your light mending and attach the support chains to the centre hook shot on the PVC support .

mark : I had to cut one of the include chains and use each half because they were too foresightful . So you might have to adjust yours as well . If all the adjustments are full , set up the light bulb in the fixture(Photo L ) .

At this point my friends , you ’re fairly much done . Plug it in , sequester an optional ( but extremely recommended ) timer to it , and you ’re ready to go .

DIY Trellis

So go forth and let your seedlings “ see the ignitor ”

Did you wish this project ? We have lots more !

More gardening project …

DIY Trellis

DIY Square Foot Garden Planting Templates

DIY Self-Watering Transplant Tray

DIY Raised Bed Trellis

DIY PVC Hoop Bed Cover

Join Fine Gardening for a destitute engaging live webinar have Dr. Janna Beckerman , a renowned plant pathologist as well as professor emerita at Purdue University and the ornamental technical manager …

When I discern a especial sand clam cactus ( Astrophytum asterias ) at the Philadelphia Flower Show a few month ago , I knew I was in trouble . With a delightful color pattern …

When we only prioritize plant life we want over plants our landscape needs , each season is filled with a never - ending list of chores : pruning , pinching , lachrymation , treating , amending , and fertilizing , with …

DIY Trellis

Video

Touring an Eco-friendly, Shady Backyard Retreat

You must be careful when you enter the backyard of garden room decorator Jeff Epping — not because you ’re likely to travel on something , but because you might be dive - bombed by a pair …