Get the feeling of costly patterned tiles at a fraction of the toll by using this tutorial on how to paint and stencil tile trading floor .
Encaustic tiles fall in all sorts ofbold patterns and gamey - contrast color compounding , but set up them often comes at a steep price . Retiling a flooris by and large a dearly-won update , and many of these intricate figure cost several dollars more per square metrical unit than basic ceramic or porcelain option . But if you love the graphic effect of patterned tiles , there ’s another elbow room to get the flavour at a fraction of the cost .
How to Paint and Stencil Tile Floors
Be sure to read through these instructions carefully before you start painting tile floors . Skipping a step could result in paint that peels , chips , or does not adhere properly to the tile .
What You Need
Step 1: Clean the tile.
Thetile should be completely cleanand free of debris before you start painting . bulge by vacuuming or sweep the base to remove any loose dirt or dust . Then thoroughly scratch the floor with a grease - abbreviate cleanser such as Krud Kutter . Be trusted to work the cleaner into the corners and grout lines , and pass over away grease with a cleanup fabric . Go over the floors again with a damp fabric to catch any remain dust or rest . Let the floor ironic , then use puma taping to mask off all baseboards and other areas where you do n’t want paint .
Step 2: Prime the tile.
Chalk - finish paint generally does n’t postulate prim out beforehand , but it ’s a good idea when paint floor tile to ensure good adhesion and a indestructible finish . For any other case of rouge , such as acrylic or latex , employ primer is an crucial footstep . Prime your tile with a bonding primer , such as KILZ Adhesion White Bonding Interior / Exterior Primer . Use a pocket-sized paintbrush to employ ground around the boundary and grout lines , then swop to a froth rolling wave for the gravid areas . Allow the primer to dry consort to the manufacturer ’s instructions . If involve , lend oneself a second pelage of fuzee and let dry .
Step 3: Paint your base color.
like to how you applied the primer , use a small paintbrush and foam roller to paint the entire tiled surface in your base colour . Note that flat - sheen paint works best to replicate the smell of unglazed encaustic or cementum tile . permit dry and apply a second coat if needed . Ensure the color is completely unanimous with no lighter spots showing through . expect at least 24 hours to provide the pigment to fully dry and fructify before stencil .
Step 4: Stencil your pattern.
Choose a stencil that matches the dimensions of your tile ( a 12x12 - column inch stencil works adept with 12 - inch square tile , for object lesson ) . Place the stencil in the nub of one roofing tile and secure the edges with panther tape . you’re able to also spray the back of the stencil with a low - tack adhesive and let it dry before positioning it on each roofing tile .
charge a foam roller or stencil brush with a little amount of your second paint color . To prevent paint from bleeding through the stencil , dab off excess rouge before each stroke . Fill in all expose areas with paint , using a pocket-size stencil skirmish as needed for more intricate pattern or hard - to - reach orbit . If desired , expend a third color to spotlight specific areas of the pattern . result the stencil in billet and let the blusher dry . If your base color is still point through after one coat , paint over the stencil again and have ironical .
Step 5: Continue stenciling across the floor.
If your stencil overlap adjoining tiles , let each painted tile dry completely before go on to the next one , or stagger the stencil to avoid messing up the impudent pigment on the previous roofing tile . To work around edge or fixtures like toilets and cesspit , match up the recession of the stencil and tile and unassailable with Felis concolor tape recording where potential . Use your free deal to flex the stencil and press it into the edge or corner as you fill in the conception . For any areas where the stencil ca n’t fit , use a humble paintbrush to continue the pattern free - hand .
Step 6: Touch up and seal.
practice a small paintbrush to touch up any post where the blusher drop or bled through the stencil . Once your designing is finished and completely wry , habituate a froth brush or roller to use a water - based clear coat for tribute . Let juiceless for at least two hours before apply a second coat . tolerate to dry out overnight and get rid of all catamount taping .
Credit: Annie Schlecther
Credit: Annie Schlecther
